AeroForce Gauges
The Interceptor gauge is 52mm (2 1/16") in diameter and will fit in all standard gauge pods of this size. A 5' cable is included with appropriate OBD2 connector. A splitter cable is included with the dual Interceptor units.
The gauge displays 2 parameters at a time, but can be programmed to cycle through up to 8 parameters during a user determined period of time. This way you can monitor several items without taking any other actions.
High intensity LEDs can be used as shift lights or warning lights to indicate when a selected parameter exceeds an entered threshold. Due to the gauges extremely fast update rate, this light is very accurate and easy to set. Once you try it you'll find you can't live without it!
Another menu option offers the ability to swap the foreground and backround colors of the display (as pictured below). Using this feature, for example, the gauge with a black backround and blue characters (negative image) becomes a blue backround with black characters (positive image). Not only can this be visually appealing but beneficial in changing lighting conditions. Positive images are easier to read in bright sunlight, negative at night.
DTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options.This essential feature will help the gauge to pay for itself the first time the check engine light comes on. Those that have modified their vehicle will find this very handy when a sensor, vacuum line, etc. has been inadvertently left disconnected, or something was just not put back together properly.
The two analog inputs can be configured through menu choices. These inputs allow the gauge to read pressure signals such as those from MAP and oil pressure sensors, analog outputs from Air/Fuel ratio kits, etc. These signal can then be read and recorded along side the other parameters obtained on the vehicle's bus.
The gauge has bi-directional controls allowing for manual control of the low and high speed fans, CASE relearn and ECU reset on GM vehicles, and on most Chrysler vehicles the transmission controller can be reset and Electronic Stability Program can also be completely turned off to improve track performance.
New optional relay output module allows you to control a 12v relay based on values of OBD2 or analog input data. I use this feature to turn on my trans cooler fan, It could also be used to run an electric radiator fan.
Last but not least, the Interceptor will measure 0-60 times, as well as 1/8 and 1/4 mile time and speeds. This is accomplished through a simple menu selection.
Installation is accomplished by simply plugging the supplied connector into the OBD2 port below the steering wheel. Literally plug-and-play!
Dual Interceptor Option: Two Interceptors can be purchased with a special splitter cable that allows both gauges to operate simultaneously.
Warranty
Aeroforce Technology warrants this product and its accessories against defects in material and workmanship for a period of 1 year from the date of purchase.
------------------------------------------------------
Sample of Parameters available:
Gas powered vehicles:
RPM
MPH
INTAKE AIR TEMP
MASS AIR FLOW
ENGINE COOLANT TEMPERATURE
INJECTOR PULSE WIDTH
DIRECT INJECTION PRESSURE
INJECTOR DUTY CYCLE
COMMANDED AIR/FUEL RATIO
AIR FUEL RATIO (FACTORY WIDE BAND O2)
ACTUAL LAMBDA “ “ “
LONG AND SHORT FUEL TRIMS
O2 SENSOR OUTPUT
MANIFOLD PRESSURE (inHg/psi) “boost” gauge.
MANIFOLD ABSOLUTE PRESS. IN kPa
IGNITION ADVANCE
KNOCK RETARD
TQ MGMT SPARK RETARD
ENGINE RUN TIME
BATTERY VOLTAGE
TRANSMISSION TEMPERATURE
IDLE AIR CONTROL COUNTS
THROTTLE POSITION PERCENTAGE
THROTTLE POSITION VOLTAGE
ENGINE LOAD
OIL PRESSURE
OIL TEMPERATURE
FUEL PRESSURE
FUEL PUMP DUTY CYCLE
INTERCOOLER OUTLET TEMP
MISFIRES
TRANSMISSION TORQUE, SLIP SPEED.
SHIFT TIME
PLUS MANY MORE!
Interceptor Features:
The Interceptor scan gauge is capable of displaying over 100 parameters, two at a time (8 using cyclic scan), at an adjustable rate of up to approximately 20 times per second. Not all are supported by every vehicle, so there is no guarantee that the Interceptor will display all of these on your particular car or truck. If the vehicle is broadcasting the parameter, the Interceptor will recognize this and make it available for display.
-------------------------------------------------------
Sample of Parameters available:
Diesel Powered Vehicles:
RPM
MPH
INTAKE AIR TEMP
INTAKE AIR 2 – 2006+ DURAMAX
MASS AIR FLOW
ENGINE COOLANT
MANIFOLD PRESSURE (BOOST) IN PSI
ENGINE RUN TIME
BATTERY VOLTAGE
TRANSMISSION TEMPERATURE
THROTTLE POSITION
ENGINE LOAD
INJECTOR RAIL PRESSURE – DESIRED
INJECTOR RAIL PRESSURE – ACTUAL
BAROMETRIC PRESSURE
ENGINE TORQUE
TRANSMISSION INPUT SPEED
TRANSMISSION OUTPUT SPEED
TRANSMISSION SLIP SPEED
TRANSMISSION TEMPERATURE
OIL PRESSURE
TURBO VANE POSITION (2004+)
PILOT AND MAIN INJECTOR TIMING
PILOT AND MAIN INJECTOR FLOW
PILOT AND MAIN INJECTOR PULSE WIDTH
EGT TEMPERATURE (2008+ Power
Stroke/Duramax)
Injector Control Pressure (Power Stroke)
DPF delta pressure 2008+
Regen status 2008+
Click below to view user manual and see the full list of parameters available for display
(for "can" Vehicles)
| parameters_features.pdf |
Please Click the link to the right for a list of vehicles supported by the Interceptor >
If your vehicle is not listed, Please give us a call (708) 691 2613
| Application Guide |
Installed in a TrailBlazer SS
Free Shipping Special!
(Lower 48 States Only)
Please contact us for a shipping quote to anywhere outside the lower 48 US States.
We Stock common color option gauges but due to the vast color combinations available, some may take a up to 5 days to ship.
Here is the information you need to send us along with your order!
In the blank box above the "Add to Cart" button below please include the following information so we know which gauge to send you!
-Vehicle make/model/year
-Display color (White, Red, Blue, Green)
Single Gauge- $229.99
Dual Gauge Kit-
$389.99
